Engineering Range

Eighteen Product Families,
Six Material Systems

Primers and bonding agents, reflective roof coatings, exposed and single-component systems, rubber asphalt and non-curing layers, bridge-and-road grades and spray-applied membranes. Every product is listed against the standard it is produced to, and made on one site in Shouguang, Shandong.

01

Surface Preparation

What the coating bonds to decides whether it lasts. These four sit under every system on this page.

4 products
Worker filling a drum with bitumen emulsion from the plant line

Emulsified Asphalt

The base coat, and the emulsion base for every coating we make.

  • 30–60% solids
  • 12 months stable
  • In-house base
Worker rolling black bitumen primer onto a concrete roof deck

Bitumen Primer

The coat that makes the membrane bond to the slab, not to the dust on it.

  • JC/T 1069-2008
  • Bond ≥0.8 MPa
  • Cold applied
Railway bridge deck with concrete parapet

Railway-Spec Primer

For railway bridge decks: dries inside two hours, flexible at −5 °C.

  • TB/T 2965-2018
  • Dry ≤2 h
  • −5 °C no crack
Worker brushing grey bonding slurry onto a concrete wall

Bonding Agent

Anchors new waterproofing to tiled, polished or previously coated surfaces.

  • 20 kg : 10 L water
  • Two-way bond
  • Cures in 12 h
02

Multi-Colour Polyester Coatings

One family, four roofs — colour, reflectivity and corrosion resistance as standard.

1 product, 4 types
Worker rolling reflective blue-grey coating across a metal factory roof

Multi-Colour Polyester Coating

Reflects three quarters of the sun and stays elastic from −20 °C to 120 °C.

  • 75% solar reflectance
  • −20 °C to 120 °C
  • Metal roof · Low absorption · Pool · Walkable
03

Exposed Roof & Single-Component

Coatings that stay on the outside — in UV, frost, ponding and foot traffic.

5 products
Coating applied across an exposed flat roof deck

High-Elastic Liquid Membrane

A liquid alternative to SBS or PVC sheet, and it heals where it is punctured.

  • JC/T 408-2005
  • 2–3 passes
  • Self-healing
Worker rolling dark grey exposed roof coating along a parapet
General · Extra

Armor Exposed Bitumen

Two grades for roofs left exposed all year — one of them for hard frost.

  • −40 °C on Extra
  • Low absorption
Basement wall being coated with a seamless waterproof membrane
951

Water-Based Polyurethane 951

Water-borne PU for basements, tunnels and tanks — no solvent, no flame.

  • JC/T 864-2008
  • 1K water-borne
  • Colour adjustable
Worker brushing blue waterproof coating around a floor drain

Single-Component Polyurethane

Goes straight from the pail, up to 3 mm in one coat.

  • GB/T 19250-2013
  • 1–3 mm per coat
  • Tolerates damp
Tunnel lining prepared for a non-exposed waterproofing layer

Water-Based Polyurethane

Non-exposed PU for underground work, bridges and wet rooms.

  • T/CWA 206-2021
  • Non-exposed
  • 2–3 passes
04

Rubber Asphalt & Non-Curing

Systems that move with the structure — and keep sealing themselves.

3 products
Worker rolling black rubber bitumen up a vertical basement wall
Type I · II

High-Tack Anti-Slip Rubber Bitumen

The layer that stops membrane sliding down a wall.

  • T/SZWA 006-2021
  • ≤1.0 mm per pass
Glossy non-curing bitumen being spread across a roof deck

Non-Curing Rubber Bitumen

Never fully cures; keeps creeping into cracks and healing itself.

  • JC/T 2428-2017
  • 99% solids
  • 115 m² per hour
Bitumen worked into a construction joint with a trowel and reinforcement

Hand-Applied Non-Curing

The non-curing system without a kettle, for flame-restricted sites.

  • Q/3202428HTQ 01-2024
  • No heating
  • Scrape or spray
05

Bridge & Road

Grades written around traffic loading, deck movement and asphalt surfacing.

3 products
Concrete bridge deck ready for its waterproofing layer
Type I · II

Polymer Modified Bitumen

For concrete bridge decks — heat resistant under the asphalt.

  • JC/T 975-2005
  • 140–160 °C
Crew applying waterproofing across a highway viaduct deck
Type I · II

Water-Based Bitumen

Water-based grade for highway bridges, interchanges and culverts.

  • JT/T 535-2015
  • 3–4 passes
Hot-melt bitumen being spread on a steel bridge deck ahead of paving

Hot-Melt Ultra-High-Tack

For steel bridge decks: fully bonded, no path for water.

  • 3.9 MPa tensile
  • 850% elongation
  • Fully bonded
06

Spray-Applied Quick-Set

Sprayed on site, set in seconds, no laps to fail.

2 products
Two-component spray gun laying quick-set bitumen on a bridge deck

Spray Quick-Set Rubber Bitumen

Two components sprayed together, gelled in four seconds.

  • JC/T 2317-2015
  • 4 s gel
  • Seamless
Worker spraying quick-set rubber bitumen onto a tunnel lining

Railway-Spec Spray Quick-Set

The railway specification of the same spray system.

  • Q/CR 517.2-2016
  • 4 s gel
  • Bridge · tunnel · metro